UPVC Window Repairs

uPVC windows are energy efficient and help to reduce heating bills. However, as they get older, problems may arise that require fixing. This could be due to damaged hinges, handles or locks.

Wooden window repair can be fairly simple for DIY enthusiasts to tackle themselves. It's less expensive than buying a new window.

Cracks

Cracks and fractures can be a major problem. Unrepaired windows can cause water intrusion and weaker barriers to cold weather, or even structural damage. It is crucial to find a local builder or repair service that specialises in the repair of uPVC frames and can demonstrate the skills, experience and equipment required to achieve the best results. This will ensure that your shattered window is fixed before it gets worse and you don't need to replace your window glass or unit.

There are many home-based solutions that can be used to repair small cracks in the glass. Super glue and masking tape are among the most commonly used products that can keep cracked glass in place for a few minutes. For deeper cracks, the tape may need to extend beyond the crack on both sides to achieve the optimal results.

Alternatively, two-part epoxy can be used to repair broken or cracked glass. Most hardware stores offer this product at around $10. Make sure your work area is properly prepared before mixing the epoxy. Also, ensure you have all the equipment needed to complete the task.

If you find that your lower or upper sash has difficulty raising, it is likely because the cords attached to the sashweights are damaged. This is an easy fix that can be accomplished with a ladder and a flathead screwdriver. Replacing a drip cap that has rot is another simple repair that can be done at home. The majority of home centers have a drip caps that are not rot free and can be easily nailed or caulked in place. Verify that the glass in double or triple-paned window is not damaged. This is due to the gases that are leaking out between the panes contribute to improving energy efficiency. They should be retained, not escaping.

Water Leaks

If your uPVC window is leaking, it could cause damage to your interior and cause costly repairs. Water leaks can also damage the structure of your home and can cause mold growth. It's important to address any problems caused by leaking windows right away to minimize damage.

A damaged sealant around window frames is a common reason for leaks. Silicone caulking can restore the seal to its original state and prevent leakage. It is also essential to look for cracks and gaps in the frame, as well as in the brick or stone walls that surround your windows.

A blocked drainage hole or faulty Flashing are two other common causes of leaking windows. Make sure that the drainage holes have not been clogged or blocked, particularly after a heavy downpour. Also, you should check the windows' flashing to ensure that it's well-sealed.

Lastly, it's important to check that your drip cap isn't broken or rotten. A drip cap that is rotten or one that is missing can allow water from above to get into your window and cause structural damage. Replacing the drip cap that is leaky isn't a daunting task. It's as easy as purchasing the new one and nailing it in place.

It's an excellent idea to have your windows tested for water-tightness by a qualified. They can make use of a device to measure the water-tightness of your windows and ensure that they meet the standards of the industry. If your windows fail the test, they'll have to be replaced. This is a cost-effective repair but it's worth it for the security and safety of your family.

Sagging

If your windows do not close properly, it could lead to a number issues including drafts, condensation and an increase in your energy bills. It could also mean that the windows weren't installed correctly or the sealant has worn out. There are a few things you can try to fix the issue.

In order to repair your window properly it is essential to set up a workspace with ample natural light. Start by laying down newspapers or an old blanket to shield the flooring from any splinters and drips that may fall from windows while you work.

Use a white cloth, soaked in a solution of detergent and water. This will prevent any stains of color UPVC repair appearing on your windows. If you're ready to begin working on your uPVC windows, begin by making a note of where the hinge channel should be situated. Unscrew the channel, and then fill the screw holes in the frame with epoxy (for uPVC frames) or wood filler. Make sure you smooth the hole before it sets.

Reinstall the hinge channel after the holes are filled. Make sure you center it on the window jamb and drill the screw holes about a quarter inch away from the original locations.

Then, take a measurement of the length of the spindle protruding from the underside of your handle and then order an alternative online or bring your old one in to the hardware store to purchase a new. Then, take the setscrew off the operator shaft. Flatten it to allow the set screw to be locked onto the shaft. Now, your uPVC window should be closing smoothly.

Broken Hinges

It will be difficult to open or closing your uPVC windows in the event that the hinges are damaged or aren't working properly. This can cause an issue with security and stop your home from staying warm or cool. You can easily get an entirely new hinge for your uPVC window. It's crucial to choose the right hinge for your windows.

This is because the hinges have to be the same size to fit inside the window frame. The most popular hinge for uPVC windows is standard 18mm or UPVC 15mm hinges for windows. However, there are specialised types of hinges for windows that can be used on other types of frames such as wooden frames. The right type of hinge can help you avoid common issues with your windows.

There are many reasons why your window hinges could have become stiff or loose. One of the most common causes is that the hinges are not tightened enough. To test this, take a screwdriver to locate the friction screw at the end of the hinge. Then loosen it. Then, you can adjust it by turning it in either direction.

Contact Preston Glass Fix if your UPVC window's hinges don't work correctly. We can offer an immediate fix. Our technicians will evaluate the condition of your hinges for your windows and advise you on the best solution for your needs. We can replace your window hinges, re-tension them, or install new locking mechanisms to ensure that your UPVC windows are secure and safe for the long haul.

Faulty Locks

UPVC window mechanisms and locks are an important part of security for your home. They make it difficult to open windows without breaking into the house. It can be frustrating when a lock fails, however, you don't have to replace the entire window.

It's often an issue that is minor and could have been easily prevented with regular maintenance. This is the reason we recommend having your uPVC windows serviced regularly with our annual maintenance program to minimize the risk of having problems.

Most modern uPVC windows have locks that operate by pushing the handle's nose across a wedge block then turning the handle to close the lock. They are very efficient in keeping the window locked, but over time, they could begin to fail if they're not properly maintained. We recommend applying WD-40 to the lock every couple of times a year.

If you find that your uPVC window doctor isn't opening or closing as quickly as it used to, or if the lock doesn't work correctly, it could be a problem with the locking gearboxes in the frame. This can be difficult to access as it requires removing the seals around the frame of the window, and removing the handle.

A locksmith who specializes in UPVC repair will be able to identify the problem quickly and replace the malfunctioning locking mechanism using a precise replacement. This quick and simple fix could save you hundreds of dollars by not having to buy new windows.