Repairs to uPVC Windows

uPVC is a great option for modern homes. They are durable, long-lasting and easy to maintain. They do not rot or rust like timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will save you from unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and even be fatal. It is essential to take the time to ensure that you're doing all you can to ensure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace them, and the new window is usually able to fit into the frame that was previously installed easily. If you have double-paned windows that are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this situation, it is necessary to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you plan attempt to remove the glass panes yourself, it is essential to wear appropriate safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth before you begin working on the window panes, so that any shards fall onto the fabric and not onto the floor, where they could be trampled.

It's a great idea to tape the gap once the glass is removed. This will prevent drafts and water from entering your property until a professional arrives to repair the window. It also acts as an obstacle to stop criminals from getting into your home. If the gap between the door and the window is substantial, you may want to use a security screen that also includes a window. This will give you the best of both.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. However, with time, they may be afflicted by a variety of issues, including sliding. A sagging window in uPVC can cause issues with light, draughts and even security. It is crucial to act immediately if you discover that your uPVC windows are sliding.

To fix a sagging window you can try to reposition the hinges. First, you'll need to open the windows so you can access the frame. After that, repairmywindowsanddoors using an screwdriver, take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after you have relocated your hinges. If you are happy with the fit of your window, you can tighten screws to secure them in place.

If you can't reposition the hinges, you may require replacing the seal. As time passes, rubber seals lose their elasticity and dry out, which causes them to lose tightness. If this happens, it's important to replace the seal as soon as possible to ensure your uPVC windows remain watertight and RepairMyWindowsAndDoors draught-proof.

uPVC handles may also become loose. The majority of the time it is due to screws that have come loose over time. However, it can occur because the handle mechanism has worn out. Fortunately, it's easy to repair the loose uPVC window handle yourself. You'll first need to close the window and do an initial fitting. The joint at the corner of the sash should be aligned with the joint on the casing. If it does not you can use a screwdriver to loosen the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is essential to take action if you awake each day to discover mouldy walls and wet floors. The leaks of water through windows could cause structural damage to your home and also affect your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a relatively easy fix and should be undertaken by any competent DIYer. Depending on the severity of the problem the caulking used previously may require removal before a fresh layer can be applied. It is essential to keep in mind that when it is about uPVC window repairs, do not be tempted to 'over-caulk and then make the area harder to clean and could reduce the efficiency of your energy.

Check that any drainage holes are free of debris inside them and that the sill pan is angled correctly to drain away from the window. In more serious cases, you may need to replace the window.

Mold spots and rotten sills are also signs of water leakage. This fungus thrives in damp conditions and can quickly spread across the house.

If the leakage is occurring between the double-glazed glass it is more likely that the problem is related to the seal, not the frame. It is also possible to be corrected by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open with a breeze, repairmywindowsanddoors it may be hinges at the fault. Anyone with the skills to fix them can replace the hinges in a matter of minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that use hinges and, just like any mechanical component they can wear down over time. It's very simple to replace a hinge on a window, but it's easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. This can be done by looking for the arrow on each hinge, this indicates the direction in which the window should be opened.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a certain way or due to inadequate installation at the factory. It is usually possible to fix the issue by sending us a photo via our website and we will be pleased to offer you suggestions.

Regularly lubricating hinges is also essential. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. This must be done at a minimum every year. WD40 and other solvent based lubricants are not recommended as they could damage parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a few various factors. The hinges, also due to wear and tear can become misaligned, this causes a gap to form where the sash meets the frame. If they are damaged beyond repair, it may be necessary to have them realigned. The second is the interlock, which is on the hinge side of the window, may be misaligned. Again, double glazing it may be feasible to give them a clean but in some instances it could be necessary to have them replaced.

The next common reason for draughts are the window seals, these are susceptible to being worn out or damaged over time, and let air escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass. this will help in regulating indoor temperatures and again will lessen the possibility of draughts.

The last way to reduce the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler that can be put on top of your window sill. They will keep your home warm by blocking out cold air.

The windows made of upvc can keep providing excellent insulation and security for your home with a little regular maintenance and repairs. It is essential to remember that all windows eventually wear out and it is cheaper to replace them rather than repair them. If you are experiencing problems with your upvc windows, it is best to seek professional assistance as soon as you can.